Chandler Fence Company

We handle the full lifecycle of a fence: repair, replacement, and new installation, across residential, commercial, and pool-code applications. Below is a breakdown of what each part of that actually involves.

Fence Repair Process

Fence repair sounds simple until you're the one trying to figure out whether a leaning section needs a new post, a new panel, or a whole new fence. Our repair process follows the same steps on every job, whether it's a single broken board or storm damage across an entire property line:

1. On-site assessment. We walk the full fence line, not just the damaged section, because a sagging panel is often a symptom of a failing post or footing further down the run.
2. Diagnosis and options. We identify the root cause — rot, rust, wind stress, impact damage, soil movement around a post footing — and explain whether a spot repair will hold or whether the surrounding sections are close enough to failure that a partial replacement makes more sense long-term.
3. Written estimate. You get a line-item quote covering materials, labor, and hardware before any work starts. No verbal ballparks that turn into a different number on the invoice.
4. Material matching. For repairs on an existing fence, we source matching wood grade, vinyl color, or iron profile wherever possible so the repaired section doesn't stand out as an obvious patch.
5. Post and footing work. Most fence failures start below grade. We reset or replace concrete footings to proper depth rather than just re-anchoring a wobbly post to a crumbling footing.
6. Panel, picket, or rail replacement. Damaged components are swapped, gaps and reveals are matched to the rest of the fence, and hardware (hinges, latches, brackets) is checked for wear at the same time — it's inefficient to fix a panel and leave a rusted hinge that fails again in six months.
7. Final walkthrough. We check gate swing and latch function, confirm the repaired section is plumb and level with the rest of the fence, and clean up job debris before we consider the work done.

Common Fence Damage and Issues We See in Chandler

Our climate creates a specific and predictable set of failure patterns. Knowing what's driving the damage on your fence helps you decide between a repair and a replacement:

• Warping and splitting wood. Wood fencing takes a beating from repeated cycles of intense desert sun heating and drying the boards, especially on west- and south-facing runs that get the most direct exposure through the afternoon. Boards cup, twist, and eventually crack along the grain.
• Rot at the base. Even in a dry climate, wood posts and the bottom few inches of pickets that sit close to irrigated landscaping or grade can absorb enough moisture to rot from the ground up while looking fine above the soil line.
• Rust on iron and chain link. Powder-coated iron and galvanized chain link generally hold up well here, but scratched coatings, cut ends, and older or lower-grade galvanization will rust, especially at welds and ground contact points.
• Sagging gates and panels. Gates are the hardest-working part of any fence — repeated opening and closing stresses hinges and the post they're mounted to. Combined with occasional strong wind gusts putting lateral load on a large gate panel, hinges loosen and posts lean over time.
• Broken or missing boards and pickets. Wind-driven impact, yard equipment, or simple age causes individual boards to crack or pop loose from fasteners; left alone, one broken board accelerates wear on the boards next to it.
• Leaning or heaving posts. Posts set too shallow, or in footings that were never properly cured, shift over time and take the whole fence line out of alignment with them.

If more than a handful of separate issues are showing up across the same fence, that's usually a sign the fence is at the end of its service life rather than a candidate for another round of spot repairs — we'll always tell you honestly which situation you're in.

Because fencing is a licensed trade in Arizona and a meaningful investment in your property, it's worth vetting a contractor the same way you would any other home improvement pro. Here's what actually matters:

• Licensing. Work with a licensed fence contractor in Chandler, not an unlicensed handyman crew. A license means the contractor is bonded and accountable if something goes wrong.
• Written, itemized estimates. A contractor who won't put pricing in writing before starting work is a red flag. You should know the cost of materials, labor, and any permit fees before you commit.
• Local permit knowledge. For any pool-adjacent fence, confirm the contractor understands Chandler's specific barrier-height and self-latching gate requirements and will handle the permit — not leave you to figure that out after the fence is already up.
• Reviews from real local customers. Look for fence contractor reviews from other Chandler homeowners specifically, not just a generic star rating. Patterns across multiple reviews — how a company handles a problem, how clean the job site was left, whether the final price matched the estimate — tell you more than the average score alone.
• Clear scope of work. A trustworthy contractor tells you plainly whether your existing fence needs a repair or a full replacement, rather than upselling a full tear-out when a section repair would genuinely hold up.

A Note on Reviews

We'd rather earn a strong reputation the honest way than manufacture one, so we're not going to fill this page with quotes we made up. If you're comparing fence contractor reviews in Chandler, we'd encourage you to look at third-party review platforms directly and weigh what patterns show up across multiple real customers — consistency in pricing, communication, and cleanup are the things worth paying attention to. We're happy to be judged on that same standard.